The Basics of Telephone Wiring
There is a widely held misconception that telephone wiring is an
impossible feat for the average non-technical person. The fact is
that small wiring jobs in your house or small business can be much
easier than you'd expect, much easier than shelling out exorbitant
hourly fees to the phone company. If you can figure out how to wire
speakers for your new stereo, you can easily wire your home or small
office for your new phone system.
Wires, plugs, and the network interface
The basics of the wiring is pretty easy to understand. Most
telephone wires are one or more twisted pairs of copper wire. The
most common type is the 4-strand (2 twisted pair). This consists of
red and green wires, which make a pair, and yellow and black wires,
which make the other pair. One telephone line needs only 2 wires.
Therefore it follows that a 4-strand wire can carry 2 separate phone
lines. The twisting keeps the lines from interfering with each
other. If you need to run more lines than just 2, you may want to
use a 6-strand, or higher. Telephone wire comes in 2 gauges, 22
gauge and 24 gauge, 24 gauge being today's standard.
There are 2 types of common modular plugs, the
RJ-11 and the
RJ-14. The most common is the RJ-11 which uses only 2 of the wires
in a 4 (or more) strand wire. This is the same kind of plug that you
use to plug your telephone into the wall. This is a 1-line plug. The
RJ-14 uses 4 wires and is used to handle 2 lines, or 2-line phones.
The first step
The first step to a small wiring job is to figure out what the
telephone company has left you to work with. What kind of network
interface (NI) do you have? They have probably left you either a
punchdown block or a network interface box. If there is a punchdown
block, and you can't get the phone company to install a modular jack
for each Plain Old Telephone Service (POTS) or central office (CO)
line, then you will need a punchdown tool to connect your inside
wiring to the NI. Most new installations consist of a network
interface box. This has modular test jacks (where you can plug a
phone in to see if the line is live) and a terminal strip from which
you run your internal wiring (IW).
From the NI you want to plan how you want the wiring in your
location to be. The star (or homerun) method is the most common
method of wiring. Each extension or phone jack is run directly from
the NI or phone system if you are installing one. The other type of
wiring is called the series (or loop) method. In this method one
long wire links all of the extensions in a series. This loop method
is not widely used anymore. As with the old type of Christmas
lights, if one goes out, all of them go out.
Using the star method, you are obviously going to have a few
wires coming from your NI, as you will have one wire for each of
your plugs. You may want to simplify the wiring and cut your wire
costs by having few of the wires carry more than one line or
Let's take a 2-line installation as an example. Each pair that
comprises each of your POTS lines should be labeled.
One of the wires of your POTS line is called the tip wire and the
other is the ring wire (see chart). There are quite a few possible
combinations of colors that could make up your pair. So in order to
connect your line to a modular jack, you need to connect the tip
wire of the POTS line to the tip wire of the jack, and also the ring
wire of the POTS line to the ring wire of the jack. In a modular
jack you have red/green and yellow/black. Most of the time you only
use the red/green pair. The green wire is the tip and the red wire
is the ring. Using the chart, figure out which of the POTS wires is
the ring and which is the tip, and connect them appropriately.
If you are not using a phone system and just want to connect your
phone jacks directly to the POTS lines, all you need to do is run
wire from the NI to your extension jacks. (This works the same way
when you're connecting the extension jacks of your phone system to
your extensions.) Just connect the correct colors to run the wire.
Again, connect tip to tip and ring to ring. As long as you are
following the tip-to-tip rule, the fact that you are connecting a
white wire with brown stripes to a green wire and a brown wire with
white stripes to a red wire shouldn't be confusing.
Remember that in order to reduce the work and materials, you may
run 2 or more lines within 1 wire. At the end of the wire you can
break out the 2 lines using an adapter which allows you to connect
line 1 to an RJ-11 plug and line 2 to another RJ-11 plug, or if you
have a 2-line phone, you can just plug an RJ-14 plug into the phone.
If you are using a small
PBX or phone
system, most likely the POTS lines (commonly called trunk lines) are
connected to the system using RJ-11 plugs. If your NI terminates
with a modular jack then the job is simple, just connect the phone
system using RJ-11 plugs. If your NI has a terminal strip (a place
where the pairs that comprise each POTS line terminate at a junction
where you directly connect the colored wires) then you would need to
either connect the lines directly to the PBX or connect a modular
jack to each of the POTS lines on the strip. Then, to wire your
phone jacks, you follow the same procedure as noted above for
connecting POTS lines directly to phone jacks.
There really isn't much else to know. If you follow these simple
instructions you should have your phones working perfectly.